OWNER'S MANUALMODEL NUMBER:PR621SNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the Owne
10Stopping the EngineTo stop the engine, pull key out (Figure 17).Adjusting the DischargeChute and Chute DeflectorTo adjust the discharge chute, move
11Operating Tips The auger blades can throw stones, toys, and other foreign objects and cause serious personal injury to the operator or to bystander
12Adjusting the Control CableChecking the Control CableRelease the control bar to remove the slack in the control cable (Figure 20).IMPORTANT: The con
13Changing the Engine OilRun the engine a few minutes before changing the oil to warm it. Warm oil flows better and carries more contaminants.4. Pla
14Servicing the Spark PlugUse a NGK BPR6ES, Champion RN9YC, or BOSCH WR6DC spark plug or equivalent.1. Stop the engine and wait for all moving parts
15Replacing the Drive BeltIf drive belt becomes worn, oil-soaked, excessively cracked, frayed, or otherwise damaged, replace the belt.1. Remove the
16StorageStoring the SnowthrowerImmediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days
17Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition
18REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96188000100)CHUTE ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4
19REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96188000100)CHUTE ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4
2Safe Operation Practices for Walk-Behind Snow ThrowersIMPORTANT: This snow thrower is capable of amputating hands and feet and throwing objects. Fai
20KEY PART NO. NO. QTY DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96188000100)HANDLE ASSEMBLY1234556SSST-Handle asm_1
21REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96188000100)AUGER ASSEMBLY9910101234567781111111212131345561114SSST-Auger asm_1NOTE: All compon
22REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96188000100)SHROUD ASSEMBLY14315161616111221089101061515714517SSST-Shroud asm_13181920192020NOTE
23REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96188000100)SHROUD ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 inch = 25.
24REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96188000100)FRAME ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4
25REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96188000100)FRAME ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4
26REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96188000100)DRIVE ASSEMBLY91234568710111213SSST-Drive asm_3NOTE: All component dimensions given
27SERVICE NOTES
28REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96188000100)ENGINE, LCT COMPLETE ENGINE-434856262
29REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR621 (96188000100)ENGINE, LCT COMPLETE ENGINE-434856KEY
3CUSTOMER RESPONSIBILITIES• Read and observe the safety rules.• Follow a regular schedule in maintaining, caring for and using your snow thrower.•
LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in mate-rials and
4KNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Com-pare the illustrations with your sn
5SetupLoose PartsUse the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1. No parts required – Unfold the ha
63. Filling the Engine with OilENGINESee engine manual.LUBRICATIONUse only high quality detergent oil rated with API service classification SG–SL. Sel
7OperationNOTE: Determine the left and right sides of the machine from the normal operating position.• Gasoline is extremely flammable and explosive.
8Starting the Engine1. Push key in (Figure 10).2. Move choke lever to left position (Figure 11).3. Firmly push in the primer 3 times with your t
9Engaging the Auger BladesTo engage the auger blades, hold the control bar against the handle (Figure 15).Disengaging the AugerBladesTo disengage the
Commentaires sur ces manuels