Poulan Pro PP5000P Manuel d'instructions télécharger pdf (Page 11)

HOW TO STOP YOUR UNIT

 Release the throttle trigger.

 Move the ON/STOP switch to the STOP

position.

ON/STOP switch

HOW TO START YOUR UNIT

WARNING:

Avoid any contact with

the muffler. A hot muffler can cause serious

burns.

Starting position

HELPFUL TIP

If your engine still does not

start after following these

instructions, please call

1--800--554--6723.

STARTING A COLD ENGINE

NOTE:

The throttle lock--out is designed to

prevent unintentional use of the throttle trig-

ger. The lock--out must be pressed with the

palm of your hand as you grip the throttle han-

dle before the trigger can be used.

1. Set unit on a flat surface.

2. Move ON/STOP switch to the ON position.

3. Move choke lever to the FULL CHOKE

position .

4. Slowly press the primer bulb 10 times.

Choke lever

Starter

handle

Primer bulb

Muffler

Throttle lock--out

5. Squeeze the throttle trigger fully and hold

through all remaining steps.

6. Pull starter rope handle sharply until engine

starts (or sounds as if it is trying to start),

but do not pull rope more than 10 times.

7. Move choke lever to HALF CHOKE posi-

tion .

8. Pull starter rope sharply until engine starts,

but no more than 10 pulls. Allow the engine

to run for 30--45 seconds.

NOTE:

If the engine doesn’t start after

10 pulls (at the HALF CHOKE position

), move the choke lever to theFULL

CHOKE position and press the

primer bulb 6 times. Squeeze andhold

the throttle trigger and pull the starter

rope 2 more times. Move the choke le-

ver to the HALF CHOKE position

and pull the starter rope until the en-

gine runs, but no more than 10 pulls. If

the engine still doesn’t start, it is prob-

ably flooded. Proceed to STARTING

A FLOODED ENGINE.

9. Once the engine starts and has ran for

10--15 seconds at the HALF CHOKE

position , move the choke lever to the

RUN position . Allow the unit to run for

30 seconds before releasing the throttle

trigger.

NOTE:

If engine dies with the choke

lever in the RUN position , move the

choke lever to the HALF CHOKE

position and pull the rope until en-

gine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1. Set unit on a flat surface.

2. Move ON/STOP switch to the ON position.

3. Move the choke lever to the HALF CHOKE

position .

4. Squeeze and hold the throttle trigger.

5. Pull starter rope sharply until engine runs,

but no more than 10 pulls.

6. Allow engine to run 30 seconds, then move

the choke lever to the RUN position .

NOTE:

If engine has not started, pull starter

rope 5 more pulls. If engine still does not run, it

is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the

choke lever in the RUN position ; then, pull

the rope to clear the engine of excess fuel. This

could require pulling the starter handle many

times depending on how badly the unit is

flooded. If the unit still doesn’t start, refer to

TROUBLESHOOTING TABLE or call

1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which

enables optional attachments to be installed.

The optional attachments are:

MODEL:

Edger PP1000E. . . . . . . . . . . . . . . . . . . . .

Cultivator PP2000T. . . . . . . . . . . . . . . . . .

Blower PP3000B. . . . . . . . . . . . . . . . . . . .

Brushcutter PP4000C. . . . . . . . . . . . . . . .

Pruner PP5000P. . . . . . . . . . . . . . . . . . . .

Pruner PP5500P. . . . . . . . . . . . . . . . . . . .

WARNING:

Always stop unit and dis-

connect spark plug before removing or instal-

ling attachments.

REMOVING TRIMMER ATTACH-

MENT (OR OTHER OPTIONAL

ATTACHMENTS)

CAUTION:

When removing or installing at-

tachments, place the unit on a flat surface for

stability.

1. Loosen the coupler by turning the knob

counterclockwise.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 59 60

Commentaires sur ces manuels

Pas de commentaire

Poulan Pro PP5000P Manuel d'instructions Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Edgers Poulan Pro PP5000P